2018 / ECLIPSE CROSS / EC - Workshop Manual
52 -INTERIOR AND SUPPLEMENTAL RESTRAINT SYSTEM(SRS) > 52A-INTERIOR > FLOOR CONSOLE ASSEMBLY > FRONT FLOOR CONSOLE ASSEMBLY > FRONT FLOOR CONSOLE ASSEMBLY REMOVAL AND INSTALLATION
REMOVAL AND INSTALLATION
 
 
<Lever type parking brake>
cautionDo not subject the SRS-ECU to any shocks when removing or installing the floor console.
Pre-removal and Post-installation Operation
  • Gearshift Lever Knob Removal and Installation (Refer to GROUP 22A - Transmission Control ) <M/T>.
  • Selector lever Knob Removal and Installation (Refer to GROUP 23A - Transmission Control ) <CVT>.
  • Instrument Panel Garnish Removal and Installation (Refer to ).
  • Instrument Panel Mat Clip Removal and Installation (Refer to ).
  • Floor Console Assembly Rear Removal and Installation (Refer to ).
 
 
Removal steps
1.Floor console box mat
2.Shift lever panel assembly
>>A<<3.Heated seat switch (front) or switch plug
4.Drive mode selector or switch plug
5.Gearshift lever cover <M/T>
Shift indicator panel assembly (Refer to GROUP 23A - Transmission Control ) <CVT>.
6.Instrument panel garnish centre
7.Touchpad controller
8.Instrument panel garnish centre <Vehicles with touchpad controller>
9.Parking brake lever cover
10.Floor console box cup holder assembly
11.Spot lamp cover
12.Spot lamp
13.Floor console box cup holder
14.Shift lever panel
 
 
Removal steps
1.Floor console side cover
2.Floor console panel
3.Floor console centre
4.Floor console bracket rear
5.Floor console bracket rear
6.Floor console bracket centre
7.Floor console bracket front
 
 
<Electric parking brake>
cautionDo not subject the SRS-ECU to any shocks when removing or installing the floor console.
Pre-removal and Post-installation Operation
  • Selector lever Knob Removal and Installation (Refer to GROUP 23A - Transmission Control ).
  • Instrument Panel Mat Clip Removal and Installation (Refer to ).
  • Floor Console Assembly Rear Removal and Installation (Refer to ).
 
 
Removal steps
<<A>>1.Instrument panel garnish centre <Vehicles with touchpad controller>
2.Floor console box mat
Instrument panel garnish (Refer to ).
3.Shift lever panel assembly
>>A<<4.Heated seat switch (front) or switch plug
5.Drive mode selector or switch plug
6.Electric parking brake switch
Shift indicator panel assembly (Refer to GROUP 23A - Transmission Control ).
7.Instrument panel garnish centre
8.Touchpad controller
9.Floor console box cup holder assembly
10.Spot lamp cover
11.Spot lamp
12.Floor console box cup holder
13.Shift lever panel
 
 
Removal steps
1.Floor console side cover
2.Floor console panel
3.Floor console centre
4.Floor console bracket rear
Electric parking brake ECU (Refer to GROUP 36 - Electric Parking Brake ECU ).
5.Floor console bracket rear
6.Floor console bracket centre
7.Floor console bracket front
 
 
REMOVAL SERVICE POINT
 
 
<<A>> INSTRUMENT PANEL GARNISH CENTRE REMOVAL
 
Remove the engagement between each claw on the instrument panel garnish centre and the shift lever panel according to the steps below.
1. Lift the instrument panel garnish centre slightly and remove the engagement between claws A on the right and left side of the vehicle and the shift lever panel.
2. Remove the engagement between claw B on the front side of the vehicle and the shift lever panel.
3. Remove the engagement between claw C on the rear side of the vehicle and the shift lever panel.
 
 
 
 
INSTALLATION SERVICE POINT
 
 
>>A<< SWITCH PLUG INSTALLATION
 
Install the switch plug in the direction shown in the figure.
 
 




Yandex.Metrika
MMC-Manuals.ru