Terminal No.
|
Check item
|
Inspection conditions
|
Normal conditions
|
1
|
Backup power supply input
|
Always
|
Battery voltage
|
2
|
ECU control power supply relay drive signal
|
Electric motor switch: ON position
|
Battery voltage
|
Electric motor switch: LOCK (OFF) position
|
1 V or less
|
3
|
IG switch signal
|
Electric motor switch: ON position
|
Battery voltage
|
4
|
Quick charging power supply signal
|
Electric motor switch: ON position
|
1 V or less
|
When quick charging is in progress
|
8 to 16 V
|
5, 6
|
-
|
-
|
-
|
7
|
Brake booster vacuum sensor power supply voltage
|
Electric motor switch: ON position
|
4.7 to 5.3 V
|
8
|
Accelerator pedal position sensor (sub) power supply voltage
|
Electric motor switch: ON position
|
4.9 to 5.1 V
|
9
|
ECU control power supply input
|
Electric motor switch: ON position
|
Battery voltage
|
Electric motor switch: LOCK (OFF) position
|
1 V or less
|
10
|
ECU power supply earth
|
Electric motor switch: ON position
|
1 V or less
|
11
|
On board charging start signal
|
Electric motor switch: LOCK (OFF) position
|
Battery voltage
|
12, 13
|
-
|
-
|
-
|
14
|
Diagnosis control signal
|
Electric motor switch: ON position
|
Battery voltage
|
15
|
-
|
-
|
-
|
16
|
K-LINE communication
|
-
|
-
|
17
|
ASC OFF switch signal
|
Set the electric motor switch to the ON position and the ASC OFF
switch to OFF.
|
Battery voltage
|
Set the electric motor switch to the ON position and the ASC OFF
switch to ON.
|
1 V or less
|
18
|
-
|
-
|
-
|
19
|
Brake electric vacuum pump main relay drive signal
|
Electric motor switch: ON position
|
1 V or less
|
20
|
Brake electric vacuum pump control relay 1 drive signal
|
Set the electric motor switch to the ON position and depress the
brake pedal firmly several times.
|
Battery voltage →
1 V or less
|
21
|
Brake electric vacuum pump control relay 2 drive signal
|
Set the electric motor switch to the ON position and depress the
brake pedal firmly several times.
|
Battery voltage →
1 V or less
|
22
|
Brake booster vacuum sensor power supply earth
|
Electric motor switch: ON position
|
1 V or less
|
23
|
Accelerator pedal position sensor (sub) power supply earth
|
Electric motor switch: ON position
|
1 V or less
|
24
|
ECU control power supply input
|
Electric motor switch: ON position
|
Battery voltage
|
Electric motor switch: LOCK (OFF) position
|
1 V or less
|
25
|
ECU power supply earth
|
Electric motor switch: ON position
|
1 V or less
|
26
|
Brake electric vacuum pump main relay operation check
signal
|
Electric motor switch: ON position
|
Battery voltage
|
Electric motor switch: LOCK (OFF) position
|
1 V or less
|
27
|
Brake electric vacuum pump operation check signal
|
Set the electric motor switch to the ON position and depress the
brake pedal firmly several times.
|
1 V or less →
Battery voltage
|
28 -
33
|
-
|
-
|
-
|
34
|
Brake electric vacuum pump vacuum 1 signal
|
Electric motor switch: ON position
|
0.2 to 1.7 V
|
35
|
Accelerator pedal position sensor (sub) signal
|
Set the electric motor switch to the ON position and release the
accelerator pedal.
|
0.3 to 0.7 V
|
Set the electric motor switch to the ON position and depress the
accelerator pedal fully.
|
2.0 to 2.5 V
|
Terminal No.
|
Check item
|
Inspection conditions
|
Normal conditions
|
41
|
-
|
-
|
-
|
42
|
Accelerator pedal position sensor (main) power supply
|
Electric motor switch: ON position
|
4.9 to 5.1 V
|
43
|
Brake pedal stroke sensor power supply
|
Electric motor switch: ON position
|
4.9 to 5.1 V
|
44
|
Brake pedal stroke sensor signal
|
Set the electric motor switch to the ON position and release the
brake pedal.
|
1.4 to 3.3 V
|
Set the electric motor switch to the ON position and depress the
brake pedal fully.
|
3.4 to 4.6 V
|
45
|
Cooling fan HI relay drive signal
|
When the electric motor switch is set to the ON position and the
radiator fan is not operated (when the coolant temperature is 52°C or less and A/C
compressor switch: OFF)
|
Battery voltage
|
When the electric motor switch is set to the ON position and the
radiator fan is operated (when the coolant temperature is 52°C or more, or A/C
compressor switch: ON)
|
1 V or less
|
46
|
Cooling fan LO relay drive signal
|
When the electric motor switch is set to the ON position and the
radiator fan is not operated (when the coolant temperature is 52°C or less and A/C
compressor switch: OFF)
|
Battery voltage
|
When the electric motor switch is set to the ON position and the
radiator fan is operated (when the coolant temperature is 52°C or more, or A/C
compressor switch: ON)
|
1 V or less
|
47
|
-
|
-
|
-
|
48
|
Accelerator pedal position sensor (main) power supply earth
|
Electric motor switch: ON position
|
1 V or less
|
49
|
Brake pedal stroke sensor power supply earth
|
Electric motor switch: ON position
|
1 V or less
|
50
|
Air bag collision signal
|
-
|
-
|
51
|
Air bag collision signal earth
|
Electric motor switch: ON position
|
1 V or less
|
52
|
K-LINE communication
|
-
|
-
|
53
|
K-LINE communication
|
-
|
-
|
54, 55
|
-
|
-
|
-
|
56
|
Water pump relay drive signal
|
Electric motor switch: ON position
|
1 V or less
|
57
|
Backup lamp relay drive signal
|
Set the electric motor switch to the ON position and the selector
lever to the R position.
|
1 V or less
|
58
|
-
|
-
|
-
|
59
|
Accelerator pedal position sensor (main) signal
|
Set the electric motor switch to the ON position and release the
brake pedal.
|
0.8 to 1.2 V
|
Set the electric motor switch to the ON position and depress the
brake pedal fully.
|
4.0 to 4.8 V
|
60
|
Parking brake lamp signal
|
Set the electric motor switch to the ON position and release the
parking brake lever.
|
Battery voltage
|
Set the electric motor switch to the ON position and apply the parking
brake lever.
|
1 V or less
|
61
|
Parking brake switch signal
|
-
|
-
|
62
|
Brake switch signal
|
Release the brake pedal.
|
1 V or less
|
Depress the brake pedal fully.
|
Battery voltage
|
63
|
ST switch signal
|
Electric motor switch: START position
|
Battery voltage
|
Electric motor switch: LOCK (OFF) position
|
1 V or less
|
64
|
-
|
-
|
-
|
65
|
A/C relay drive signal
|
Electric motor switch: ON position
|
1 V or less
|
66
|
On board charging relay drive signal
|
When the electric motor switch is set to the ON position and on board
charging cable is disconnected
|
Battery voltage
|
When the electric motor switch is set to the ON position and on board
charging cable is connected
|
1 V or less
|
Terminal No.
|
Check item
|
Inspection conditions
|
Normal conditions
|
71
|
-
|
-
|
-
|
72
|
Coolant temperature sensor signal
|
When the coolant temperature is -20°C with the
electric motor switch set to the ON position
|
3.9 to 4.5 V
|
When the coolant temperature is 0°C with the electric motor
switch set to the ON position
|
3.2 to 3.8 V
|
When the coolant temperature is 20°C with the electric motor
switch set to the ON position
|
2.3 to 2.9 V
|
When the coolant temperature is 40°C with the electric motor
switch set to the ON position
|
1.4 to 2.0 V
|
When the coolant temperature is 60°C with the electric motor
switch set to the ON position
|
0.7 to 1.3 V
|
When the coolant temperature is 80°C with the electric motor
switch set to the ON position
|
0.3 to 0.9 V
|
73
|
-
|
-
|
-
|
74
|
Service plug switch signal
|
When the electric motor switch is set to the ON position, deactivate
the interlock.
|
1 V or less
|
When the electric motor switch is set to the ON position, activate
the interlock.
|
Battery voltage
|
75
|
-
|
-
|
-
|
76
|
K-LINE signal
|
-
|
-
|
77, 78
|
-
|
-
|
-
|
79
|
Coolant temperature sensor signal earth
|
Electric motor switch: ON position
|
1 V or less
|
80, 81
|
-
|
-
|
-
|
82
|
Shift position B2-range signal (main)
|
Set the electric motor switch to the ON position and the selector
lever to the C position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the C position.
|
1 V or less
|
83
|
Shift position B1-range signal (main)
|
Set the electric motor switch to the ON position and the selector
lever to the B-position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the B-position.
|
1 V or less
|
84
|
Shift position D-range signal (main)
|
Set the electric motor switch to the ON position and the selector
lever to the D position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the D position.
|
1 V or less
|
85
|
Shift position N-range signal (main)
|
Set the electric motor switch to the ON position and the selector
lever to the N position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the N position.
|
1 V or less
|
86
|
Shift position R-range signal (main)
|
Set the electric motor switch to the ON position and the selector
lever to the R position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the R position.
|
1 V or less
|
87
|
Shift position P-range signal (main)
|
Set the electric motor switch to the ON position and the selector
lever to the P position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the P position.
|
1 V or less
|
88
|
Shift position switch (main) power supply
|
Electric motor switch: ON position
|
Battery voltage
|
89
|
Shift position switch (sub) power supply
|
Electric motor switch: ON position
|
Battery voltage
|
90 -
92
|
-
|
-
|
-
|
93
|
Shift position D range signal (sub)
|
Set the electric motor switch to the ON position and the selector
lever to the D position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the D position.
|
1 V or less
|
94
|
Shift position N range signal (sub)
|
Set the electric motor switch to the ON position and the selector
lever to the N position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the N position.
|
1 V or less
|
95
|
Shift position R range signal (sub)
|
Set the electric motor switch to the ON position and the selector
lever to the R position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the R position.
|
1 V or less
|
96
|
Shift position P range signal (sub)
|
Set the electric motor switch to the ON position and the selector
lever to the P position.
|
Battery voltage
|
Set the electric motor switch to the ON position and the selector
lever to a position other than the P position.
|
1 V or less
|
97, 98
|
-
|
-
|
-
|
Terminal No.
|
Check item
|
Inspection conditions
|
Normal conditions
|
101, 102
|
-
|
-
|
-
|
103
|
On board battery charging connection signal
|
When the electric motor switch is set to the ON position and on board
charging cable is not connected
|
4.2 to 4.8 V
|
When the electric motor switch is set to the ON position, the release
button is set to ON with the on board charging cable connected
|
2.4 to 3.2 V
|
When the electric motor switch is set to the ON position, the release
button is set to OFF with the on board charging cable connected
|
1.2 to 2.0 V
|
104
|
Quick charging connection signal
|
When the electric motor switch is set to the ON position and on board
charging cable is not connected
|
Battery voltage
|
When the electric motor switch is set to the ON position and on board
charging cable is connected
|
1 V or less
|
105
|
Charging contactor drive signal
|
Electric motor switch: ON →
START position
|
Battery voltage (intermittently) →
1 V or less
|
106
|
Main contactor (-) drive signal
|
Electric motor switch: ON (before electric motor unit start)
|
Battery voltage
|
Electric motor switch: ON →
START position (after electric
motor unit start)
|
1 V or less
|
107
|
Main contactor (+) signal
|
Electric motor switch: ON (before electric motor unit start)
|
Battery voltage
|
Electric motor switch: ON →
START position (after electric
motor unit start)
|
1 V or less
|
108
|
On board battery charging connection earth
|
Electric motor switch: ON position
|
1 V or less
|
109, 110
|
-
|
-
|
-
|
111
|
Quick charging approval signal
|
When quick charging is in progress
|
10 to 16 V
|
112
|
Quick charger relay drive signal
|
Electric motor switch: ON position
|
Battery voltage
|
When quick charging is in progress
|
1 V or less
|
113
|
Water pump relay drive signal
|
Electric motor switch: ON (before electric motor unit start)
|
1 V or less
|
Electric motor switch: ON →
START position (after electric
motor unit start, coolant temperature is 45°C or more)
|
Battery voltage
|
114, 115
|
-
|
-
|
-
|
116
|
12 V DCDC converter shutdown signal
|
Electric motor switch: ON →
START position (after electric
motor unit start)
|
Battery voltage
|
117
|
Inverter shutdown signal
|
Electric motor switch: ON →
START position (after electric
motor unit start)
|
Battery voltage
|
118, 119
|
-
|
-
|
-
|
120
|
Contactor power supply input
|
Electric motor switch: ON position
|
Battery voltage
|
121 -
123
|
-
|
-
|
-
|
124
|
Quick charging start signal
|
Electric motor switch: ON position
|
Battery voltage
|
When quick charging is in progress
|
1 V or less
|
125
|
Water pump rotation signal
|
Electric motor switch: ON →
START position (after electric
motor unit start, coolant temperature is 45°C or more)
|
Pulse signal
|
126
|
-
|
-
|
-
|
127
|
12-V converter drive signal
|
Electric motor switch: ON (before electric motor unit start)
|
1 V or less
|
Electric motor switch: ON →
START position (after electric
motor unit start)
|
Battery voltage
|
128 -
130
|
-
|
-
|
-
|
)
)
)
)