|
|
|
<DRIVER’S SIDE>
Switch position
|
Battery connection
|
Tester connection
|
Specified condition
|
UP
|
- Connect terminal No.8 and the negative battery terminal.
- Connect terminal No.10 and the positive battery terminal.
|
7 -
8
|
12 V
|
OFF
|
7 -
8, 8 -
9
|
1 V or less
|
DOWN
|
8 -
9
|
12 V
|
|
|
|
<PASSENGER’S SIDE>
Switch position
|
Tester connection
|
Specified condition
|
UP
|
10 -
12, 8*
-
14
|
Continuity exists (2 Ω
or less)
|
OFF
|
8*
-
12, 8*
-
14
|
DOWN
|
10 -
14, 8*
-
12
|
|
| note |
*: Set the window lock switch to UNLOCK position.
|
|
|
<REAR LEFT SIDE>
Switch position
|
Tester connection
|
Specified condition
|
UP
|
1 -
10, 3 -
8*
|
Continuity exists (2 Ω
or less)
|
OFF
|
1 -
8*, 3 -
8*
|
DOWN
|
3 -
10, 1 -
8*
|
|
| note |
*: Set the window lock switch to UNLOCK position.
|
|
|
<REAR RIGHT SIDE>
Switch position
|
Tester connection
|
Specified condition
|
UP
|
4 -
10, 6 -
8*
|
Continuity exists (2 Ω
or less)
|
OFF
|
4 -
8*, 6 -
8*
|
DOWN
|
6 -
10, 4 -
8*
|
|
| note |
*: Set the window lock switch to UNLOCK position.
|
|
|
|
|
<DRIVER’S SIDE>
Switch position
|
Battery connection
|
Tester connection
|
Specified condition
|
UP
|
- Connect terminal No.2 and the negative battery terminal.
- Connect terminal No.10 and the positive battery terminal.
|
2 -
12
|
12 V
|
OFF
|
2 -
12, 2 -
14
|
1 V or less
|
DOWN
|
2 -
14
|
12 V
|
|
|
|
<PASSENGER’S SIDE>
Switch position
|
Tester connection
|
Specified condition
|
UP
|
7 -
10, 2*
-
9
|
Continuity exists (2 Ω
or less)
|
OFF
|
2*
-
7, 2*
-
9
|
DOWN
|
9 -
10, 2*
-
7
|
|
| note |
*: Set the window lock switch to UNLOCK position.
|
|
|
<REAR LEFT SIDE>
Switch position
|
Tester connection
|
Specified condition
|
UP
|
1 -
10, 2*
-
3
|
Continuity exists (2 Ω
or less)
|
OFF
|
1 -
2*, 2*
-
3
|
DOWN
|
3 -
10, 1 -
2*
|
|
| note |
*: Set the window lock switch to UNLOCK position.
|
|
|
<REAR RIGHT SIDE>
Switch position
|
Tester connection
|
Specified condition
|
UP
|
4 -
10, 2*
-
6
|
Continuity exists (2 Ω
or less)
|
OFF
|
2*
-
4, 2*
-
6
|
DOWN
|
6 -
10, 2*
-
4
|
|
| note |
*: Set the window lock switch to UNLOCK position.
|
|
|
|
|
Switch position
|
Tester connection
|
Specified condition
|
UP
|
4 -
5, 6 -
7
|
Continuity exists (2 Ω
or less)
|
OFF
|
4 -
5, 7 -
8
|
DOWN
|
4 -
6, 7 -
8
|
|
|
|
|
1.Connect a battery to the motor terminals and check that the motor runs smoothly.
|
|
|
2.Check that the motor runs in the opposite direction when the battery is connected with the polarity reversed.
|
|
|
3.If a defect is found, replace the power window motor assembly.
|
|
<FRONT DOOR>
Battery connection
|
Slider position
|
- Connect terminal No. 1 to the negative battery terminal.
- Connect terminal No. 4 to the positive battery terminal.
|
UP
|
- Connect terminal No. 4 to the negative battery terminal.
- Connect terminal No. 1 to the positive battery terminal.
|
DOWN
|
|
|
<REAR DOOR>
Battery connection
|
Slider position
|
- Connect terminal No. 4 to the negative battery terminal.
- Connect terminal No. 1 to the positive battery terminal.
|
UP
|
- Connect terminal No. 1 to the negative battery terminal.
- Connect terminal No. 4 to the positive battery terminal.
|
DOWN
|
|
)
)
)
)
)
