Item No.
|
M.U.T.-III display
|
Inspection conditions
|
Normal conditions
|
1
|
Power switch signal
|
When the electric motor switch is in the ON position
|
ON
|
Other than above
|
OFF
|
2
|
Power switch (ST) signal
|
When the electric motor switch is in the START position
|
ON
|
Other than above
|
OFF
|
3
|
Brake SW
|
When the brake pedal is being depressed (Stop lamp switch: ON)
|
ON
|
Other than above
|
OFF
|
4
|
Parking brake switch
|
When the parking brake lever is pulled up (Parking brake switch:
ON)
|
ON
|
Other than above
|
OFF
|
5
|
12 V DC/DC F/B signal
|
- When the Ready indicator is lit
- When the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
6
|
Interlock switch
|
When the service plug is removed
|
OFF
|
When the service plug is installed
|
ON
|
7
|
Radiator fan 1 relay diagnosis (cooling fan LO relay)
|
When the radiator fan relay is operating at low speed
|
ON
|
Other than above
|
OFF
|
8
|
Radiator fan 2 relay diagnosis (cooling fan HI relay)
|
When the radiator fan relay is operating at high speed
|
ON
|
Other than above
|
OFF
|
9
|
Charging contactor (diagnosis)
|
- Immediately before the Ready indicator is lit
- Immediately before the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
10
|
Main contactor [+] (diagnosis)
|
- When the Ready indicator is lit
- When the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
11
|
Main contactor [-] (diagnosis)
|
- When the Ready indicator is lit
- When the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
12
|
On board charger power supply relay (diagnosis)
|
- When the M.U.T.-III is connected
- When charging by the on board charger is in progress (When the on board transformer
is operating)
|
ON
|
Other than above
|
OFF
|
13
|
A/C power supply relay (diagnosis)
|
- 10 seconds after the electric motor switch is set to
the ON position
- When the electric motor switch is in the START position
|
ON
|
Other than above
|
OFF
|
14
|
Back lamp relay (diagnosis)
|
When the selector lever is in the position other than the R position
|
OFF
|
When the selector lever is in the R position
|
ON
|
15
|
Diagnosis control terminal connection
|
When the M.U.T.-III is not connected
|
OFF
|
When the M.U.T.-III is connected
|
ON
|
16
|
TCL OFF switch
|
When the ASC OFF switch is set to OFF
|
OFF
|
When the ASC OFF switch is set to ON
|
ON
|
17
|
Quick charger connection flag
|
When quick charging is not in progress
|
OFF
|
When quick charging is in progress
|
ON
|
18
|
Quick charger ready signal
|
When quick charging is not in progress
|
OFF
|
When quick charging is in progress
|
ON
|
19
|
Quick charging start signal
|
When quick charging is not in progress
|
OFF
|
When quick charging is in progress
|
ON
|
20
|
On board charging start signal
|
When charging by the on board charger is not in progress (When the
on board transformer is not operating)
|
OFF
|
When charging by the on board charger is in progress (When the on
board transformer is operating)
|
ON
|
22
|
Timer charging flag
|
Always
|
ON
|
23
|
Timed air conditioning flag
|
Always
|
OFF
|
24
|
Timer presetting flag
|
Always
|
ON
|
25
|
Shift position sw P
|
When the selector lever is in the position other than the P position
|
OFF
|
When the selector lever is in the P position
|
ON
|
26
|
Shift position sw R
|
When the selector lever is in the position other than the R position
|
OFF
|
When the selector lever is in the R position
|
ON
|
27
|
Shift position sw N
|
When the selector lever is in the position other than the N position
|
OFF
|
When the selector lever is in the N position
|
ON
|
28
|
Shift position sw D
|
When the selector lever is in the position other than the D position
|
OFF
|
When the selector lever is in the D position
|
ON
|
29
|
Shift position sw E (JPN)/ B (EU)
|
When the selector lever is in the position other than the B position
|
OFF
|
When the selector lever is in the B position
|
ON
|
30
|
Shift position sw B (JPN)/ C (EU)
|
When the selector lever is in the position other than the C position
|
OFF
|
When the selector lever is in the C position
|
ON
|
31
|
Inhibitor sw P
|
When the selector lever is in the position other than the P position
|
OFF
|
When the selector lever is in the P position
|
ON
|
32
|
Inhibitor sw R
|
When the selector lever is in the position other than the R position
|
OFF
|
When the selector lever is in the R position
|
ON
|
33
|
Inhibitor sw N
|
When the selector lever is in the position other than the N position
|
OFF
|
When the selector lever is in the N position
|
ON
|
34
|
Inhibitor sw D
|
When the selector lever is in the position other than the D position
|
OFF
|
When the selector lever is in the D position
|
ON
|
35
|
Inhibitor sw E (JPN)/ B (EU)
|
When the selector lever is in the position other than the B position
|
OFF
|
When the selector lever is in the B position
|
ON
|
36
|
Inhibitor sw B (JPN)/ C (EU)
|
When the selector lever is in the position other than the C position
|
OFF
|
When the selector lever is in the C position
|
ON
|
37
|
Air bag collision signal
|
When the air bag is not deployed
|
OFF
|
When the air bag is deployed
|
ON
|
50
|
IGCT control power supply relay
|
Always
|
ON
|
51
|
Charging contactor output (diagnosis)
|
- Immediately before the Ready indicator is lit
- Immediately before the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
52
|
Main contactor (+)
|
- When the Ready indicator is lit
- When the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
53
|
Main contactor (-)
|
- When the Ready indicator is lit
- When the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
54
|
Motor inverter shutdown
|
When the selector lever is in the R, D, B, or C position while the
Ready indicator is lit
|
ON
|
Other than above
|
OFF
|
55
|
12 V DC/DC CONV shutdown
|
- When the Ready indicator is lit
- When the charging indicator is lit
|
ON
|
Other than above
|
OFF
|
56
|
Radiator fan 1 relay (cooling fan LO relay)
|
When the radiator fan relay is operating at low speed or high speed
|
ON
|
Other than above
|
OFF
|
57
|
Radiator fan 2 relay (cooling fan HI relay)
|
When the radiator fan relay is operating at high speed
|
ON
|
Other than above
|
OFF
|
58
|
Water pump relay
|
When the water pump is operating
|
ON
|
Other than above
|
OFF
|
59
|
On board charger power supply relay
|
- When the M.U.T.-III is connected
- When charging by the on board charger is in progress (When the on board transformer
is operating)
|
ON
|
Other than above
|
OFF
|
60
|
A/C relay
|
- 10 seconds after the electric motor switch is set to
the ON position
- When the electric motor switch is in the START position
|
ON
|
Other than above
|
OFF
|
61
|
Back-lamp relay
|
When the selector lever is in the position other than the R position
|
OFF
|
When the selector lever is in the R position
|
ON
|
62
|
Quick charging contactor
|
When quick charging is not in progress
|
OFF
|
When quick charging is in progress
|
ON
|
63
|
Vacuum P fail-safe relay (brake electric vacuum pump main relay)
|
When the electric motor switch is in the ON position
|
ON
|
64
|
Vacuum pump relay 1 (Brake electric vacuum pump control relay 1)
|
- When the electric motor switch is in the ON position
- When the brake electric vacuum pump is operating
|
ON
|
65
|
Vacuum pump relay 2 (Brake electric vacuum pump control relay 2)
|
- When the electric motor switch is in the ON position
- When the brake electric vacuum pump is operating
|
ON
|
66
|
Quick charging approval signal
|
When quick charging is not in progress
|
OFF
|
When quick charging is in progress
|
ON
|
75
|
Accelerator sensor 1 power supply voltage
|
-
|
4.9 V - 5.1 V
|
76
|
Accelerator sensor 2 power supply voltage
|
-
|
4.9 V - 5.1 V
|
78
|
Accelerator sensor 1 voltage
|
When the accelerator pedal is released
|
0.8 V - 1.2 V
|
When the pedal is depressed
|
Increases in response to the depression amount.
|
Fully open
|
4.0 V - 4.8 V
|
79
|
Accelerator sensor 2 voltage
|
When the accelerator pedal is released
|
0.8 V - 1.2 V
|
When the pedal is depressed
|
Increases in response to the depression amount.
|
Fully open
|
4.0 V - 4.8 V
|
81
|
Vacuum pump vacuum pressure sensor voltage (brake electric vacuum pump
power supply voltage)
|
-
|
4.74 V - 5.00 V
|
82
|
Coolant temperature sensor voltage
|
When the coolant temperature is 100°C
|
0.5 V or less
|
When the coolant temperature is -30°C
|
4.2 V or more
|
83
|
Control power supply pressure (partial pressure of
control power supply value by 8/16)
|
When the voltage of the auxiliary battery is 8 V
|
2.14 V or more
|
When the voltage of the auxiliary battery is 16 V
|
4.28 V or less
|
84
|
Vacuum pump relay 2 voltage (partial pressure of brake
electric vacuum pump control relay 2 voltage by 8/16)
|
When the voltage of the auxiliary battery is 8 V
|
2.14 V or more
|
When the voltage of the auxiliary battery is 16 V
|
4.28 V or less
|
85
|
B/P stroke sensor voltage
|
When the accelerator pedal is released
|
2 V - 3 V
|
When the pedal is depressed
|
MAX 4.4 V
|
86
|
B/P stroke sensor power supply
|
-
|
About 5 V
|
87
|
Brake sensor stroke value
|
When the pedal is depressed
|
MAX 40 mm
|
100
|
Control power supply voltage
|
-
|
8.0 V - 16.0 V
|
127
|
Accelerator opening angle (for control)
|
When the pedal is not depressed
|
1.00 V or more
|
When pedal is depressed
|
4.65 V or less
|
128
|
Vehicle speed
|
When the vehicle is driven at the speed of 40 km/h
|
approximately. 40 km/h
|
142
|
Charging contactor seizure flag
|
When the charging contactor is not seized
|
OFF
|
When the charging contactor is seized
|
ON
|
143
|
Contactor (+) seizure flag
|
When the main contactor (+) is not seized
|
OFF
|
When the main contactor (+) is seized
|
ON
|
144
|
Contactor (-) seizure flag
|
When the main contactor (-) is not seized
|
OFF
|
When the main contactor (-) is seized
|
ON
|
190
|
B/P stroke sensor installation
|
Not checked or improperly installed
|
NG
|
Properly installed
|
OK
|
204
|
Coolant temperature
|
When the coolant temperature is -20°C
|
- 20 °C
|
When the coolant temperature is 0°C
|
0 °C
|
When the coolant temperature is 20°C
|
20 °C
|
When the coolant temperature is 40°C
|
40 °C
|
When the coolant temperature is 80°C
|
80 °C
|
205
|
WP rotation
|
When stopped
|
0 r/min
|
Being operated
|
1,000 to 5,000 r/min
|
206
|
On board battery charging connection signal voltage
|
When the regular charging connection is not connected
|
4.24 V - 4.65 V
|
When the regular charging connection is connected and the release
button is ON
|
1.25 V - 1.91 V
|
When the regular charging connection is connected and the release
button is OFF (while on board charging)
|
2.42 V - 3.10 V
|
207
|
On board battery charging connection signal
|
When the regular charging connection is not connected
|
Not available
|
When the regular charging connection is connected and the release
button is ON
|
Release ON
|
When the regular charging connection is connected and the release
button is OFF (while on board charging)
|
Release OFF
|
251
|
VP: Fail-safe relay contact point state (brake electric vacuum pump
main relay)
|
When the electric motor switch is set to the ON position
|
ON
|
252
|
VP: Control relay 1 state (brake electric vacuum pump
control relay 1)
|
When the brake electric vacuum pump is operating with the electric
motor switch set to the ON position
|
ON
|
Other than above
|
OFF
|
253
|
VP: Control relay 2 state (brake electric vacuum pump
control relay 2)
|
When the brake electric vacuum pump is operating with the electric
motor switch set to the ON position
|
ON
|
Other than above
|
OFF
|
254
|
VP: Motor drive state
|
When the brake electric vacuum pump is operating with the electric
motor switch set to the ON position
|
ON
|
Other than above
|
OFF
|
255
|
VP: Buzzer drive state
|
When the brake warning buzzer is operating with the electric motor
switch set to the ON position
|
ON
|
Other than above
|
OFF
|
256
|
VP: Brake warning indicator drive state
|
When the brake warning indicator is operating with the electric motor
switch set to the ON position
|
ON
|
Other than above
|
OFF
|
259
|
VP: Vehicle speed
|
When the vehicle is driven at the speed of 40 km/h
|
approximately. 40 km/h
|
