MSB is released for this page as follows:
| Release Date | Subject | MSB No. |
|---|
| 2011-09-20 | i-MiEV TECHNICAL INFORMATION MANUAL AND WORKSHOP MANUAL | MSB-11E00-506A |
Code No. C2021:
Brake booster vacuum sensor failure output voltage (VP)
BRAKE BOOSTER VACUUM SENSOR CIRCUIT
OPERATION
The 5-V power is supplied from EV-ECU to the brake booster vacuum sensor, then the brake vacuum
is converted to the voltage and output to the EV-ECU.
DIAGNOSIS CODE SET CONDITIONS
- If the setting range deviation of the brake booster vacuum
sensor output voltage continues, the diagnosis code No. C2021 will be set.
PROBABLE CAUSES
- Damaged wiring harness or connector(s)
- Malfunction of the brake booster vacuum sensor
- Malfunction of the EV-ECU
|
|
STEP 1. Voltage measurement at C-106 EV-ECU connector
|
|
|
(1)With the C-106 EV-ECU connector connected, and measure by backprobing.
|
|
|
(2)Turn the electric motor switch to the "ON" position.
|
|
|
(3)Measure the brake booster vacuum sensor output voltage between the C-106 EV-ECU
connector terminal No. 34 and the body earth.
OK: 0.1 to 4.5 V
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 4.
|
|
|
|
|
|
 Go to Step 2.
|
|
|
|
|
|
STEP 2. Connector check: C-106 EV-ECU connector, B-28 intermediate
connnector, A-105 brake booster vacuum sensor connector
|
|
|
Q.
I s the check result normal?
|
|
|
Go to Step 3.
|
|
|
|
|
|
Repair the damaged connector.
|
|
|
|
|
|
STEP 3. Check the wiring harness between A-105 brake booster vacuum
sensor connector terminal No. 1 and C-106 EV-ECU connector terminal No. 34.
|
|
|
Check the signal lines for open circuit and short to earth.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 4.
|
|
|
|
|
|
Repair the wiring harness.
|
|
|
|
|
|
STEP 4. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is set to the EV-ECU.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Set the electric motor switch from the "LOCK" (OFF) position to the "ON" position.
|
|
|
(3)Check if the diagnosis code is set.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Replace the brake booster vacuum sensor. (Refer to GROUP 35A - Master
Cylinder Assembly and Brake Booster Assembly  <LHD>, <RHD>.)
Then go to Step 5.
|
|
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction .)
|
|
|
|
|
|
STEP 5. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is set to the EV-ECU.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Set the electric motor switch from the "LOCK" (OFF) position to the "ON" position.
|
|
|
(3)Check if the diagnosis code is set.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Replace the EV-ECU. (Refer to .) Then go
to Step 6.
|
|
|
|
|
|
The diagnosis is complete.
|
|
|
|
|
|
STEP 6. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is set to the EV-ECU.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Set the electric motor switch from the "LOCK" (OFF) position to the "ON" position.
|
|
|
(3)Check if the diagnosis code is set.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Return to Step 1.
|
|
|
|
|
|
The diagnosis is complete.
|
|
|
|
MMC-Manuals.ru
)
)
)
)
)
)