BMU DATA LIST REFERENCE TABLE


Display on M.U.T.-III
 Item No.
 Inspection item
 Inspection conditions
 Value to be determined as normal
 Code No. or inspection procedure No.
 Reference page
Battery current
 12
 Electric current
 Electric motor switch: ON
 0 A
 Code No. P1A40, P1A41, P1A42, P1A43
 , , ,
During regular charging*1
 0 - 10 A

  • Electric motor switch: READY
  • A/C set temperature: maximum temperature
  • MAX switch: ON

 Difference is less than 10 A among main battery current sensor (high) control value, main battery current sensor (low) control value and displayed value.
BAT.current HI control value
 13
 Main battery current sensor (high) control value
 Electric motor switch: ON
 0 A
 Code No. P1A40, P1A42, P1A43
 , ,
During regular charging*1
 0 - 10 A

  • Electric motor switch: READY
  • A/C set temperature: maximum temperature
  • MAX switch: ON

 Value changes by value less than 0 A.
BAT.current LO control value
 14
 Main battery current sensor (low) control value
 Electric motor switch: ON
 0 A
 Code No. P1A41, P1A42, P1A43
 , ,
During regular charging*1
 0 - 10 A

  • Electric motor switch: READY
  • A/C set temperature: maximum temperature
  • MAX switch: ON

 Value changes by value less than 0 A.
BAT.current HI sensor
 15
 Main battery current sensor (high)
 Electric motor switch: ON
 2.45 - 2.55 V
 Code No. P1A40, P1A42, P1A43
 , ,
During regular charging*1
 2.45 - 2.61 V

  • Electric motor switch: READY
  • A/C set temperature: maximum temperature
  • MAX switch: ON

 Value changes by value less than 2.55 V.
BAT.current LO sensor
 16
 Main battery current sensor (low)
 Electric motor switch: ON
 2.45 - 2.55 V
 Code No. P1A41, P1A42, P1A43
 , ,
During regular charging*1
 2.45 - 3.21 V

  • Electric motor switch: READY
  • A/C set temperature: maximum temperature
  • MAX switch: ON

 Value changes by value less than 2.55 V.
Battery cooling fan relay output
 18
 Main battery cooling fan relay output
 Electric motor switch: ON
 OFF
 Code No. P1A47, P1A4E
 ,
Right after starting regular charge*1
 ON → OFF (after several seconds elapse)
Leak sensor output (Precheck)
 19
 Main battery ground fault detector output (pre-check signal)
 Electric motor switch: ON
 OFF
 -
 -
Leak detection flag
 20
 Detecting ground fault flag
 Electric motor switch: ON
 OFF
 Code No. P1A44, P1A46
 ,
OR power supply voltage
 29
 BMU control power supply voltage
 Electric motor switch: ON
 Voltage lower than battery power supply by approximately 1 V
 Code No. P1A4C
IGCT power supply voltage
 30
 EV-ECU control power supply voltage
 Electric motor switch: ON
 Battery voltage
 Code No. P1A4D
Battery cooling fan PWM output
 31
 Main battery cooling fan PWM signal
 Electric motor switch: ON
 100 %
 Code No. P1A48
Right after starting regular charge*1
 10 % → 100 % (after several seconds elapse)
Battery cooling fan rotations
 32
 Main battery cooling fan rotational speeds
 Electric motor switch: ON
 0 r/min
 Code No. P1AC1, P1AC2, P1AC3
 , ,
Right after starting regular charge*1
 More than 1,620 r/min → 0 r/min (after several seconds elapse)
CMU ID01 Cell A Balancer drive
 188
 CMU ID01 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A8E
CMU ID01 Cell B Balancer drive
 189
 CMU ID01 battery cell B balancer driving status
CMU ID01 Cell C Balancer drive
 190
 CMU ID01 battery cell C balancer driving status
CMU ID01 Cell D Balancer drive
 191
 CMU ID01 battery cell D balancer driving status
CMU ID01 Cell E Balancer drive
 192
 CMU ID01 battery cell E balancer driving status
CMU ID01 Cell F Balancer drive
 193
 CMU ID01 battery cell F balancer driving status
CMU ID01 Cell G Balancer drive
 194
 CMU ID01 battery cell G balancer driving status
CMU ID01 Cell H Balancer drive
 195
 CMU ID01 battery cell H balancer driving status
CMU ID02 Cell A Balancer drive
 196
 CMU ID02 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A8F
CMU ID02 Cell B Balancer drive
 197
 CMU ID02 battery cell B balancer driving status
CMU ID02 Cell C Balancer drive
 198
 CMU ID02 battery cell C balancer driving status
CMU ID02 Cell D Balancer drive
 199
 CMU ID02 battery cell D balancer driving status
CMU ID02 Cell E Balancer drive
 200
 CMU ID02 battery cell E balancer driving status
CMU ID02 Cell F Balancer drive
 201
 CMU ID02 battery cell F balancer driving status
CMU ID02 Cell G Balancer drive
 202
 CMU ID02 battery cell G balancer driving status
CMU ID02 Cell H Balancer drive
 203
 CMU ID02 battery cell H balancer driving status
CMU ID03 Cell A Balancer drive
 204
 CMU ID03 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A90
CMU ID03 Cell B Balancer drive
 205
 CMU ID03 battery cell B balancer driving status
CMU ID03 Cell C Balancer drive
 206
 CMU ID03 battery cell C balancer driving status
CMU ID03 Cell D Balancer drive
 207
 CMU ID03 battery cell D balancer driving status
CMU ID03 Cell E Balancer drive
 208
 CMU ID03 battery cell E balancer driving status
CMU ID03 Cell F Balancer drive
 209
 CMU ID03 battery cell F balancer driving status
CMU ID03 Cell G Balancer drive
 210
 CMU ID03 battery cell G balancer driving status
CMU ID03 Cell H Balancer drive
 211
 CMU ID03 battery cell H balancer driving status
CMU ID04 Cell A Balancer drive
 212
 CMU ID04 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A91
CMU ID04 Cell B Balancer drive
 213
 CMU ID04 battery cell B balancer driving status
CMU ID04 Cell C Balancer drive
 214
 CMU ID04 battery cell C balancer driving status
CMU ID04 Cell D Balancer drive
 215
 CMU ID04 battery cell D balancer driving status
CMU ID04 Cell E Balancer drive
 216
 CMU ID04 battery cell E balancer driving status
CMU ID04 Cell F Balancer drive
 217
 CMU ID04 battery cell F balancer driving status
CMU ID04 Cell G Balancer drive
 218
 CMU ID04 battery cell G balancer driving status
CMU ID04 Cell H Balancer drive
 219
 CMU ID04 battery cell H balancer driving status
CMU ID05 Cell A Balancer drive
 220
 CMU ID05 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A92
CMU ID05 Cell B Balancer drive
 221
 CMU ID05 battery cell B balancer driving status
CMU ID05 Cell C Balancer drive
 222
 CMU ID05 battery cell C balancer driving status
CMU ID05 Cell D Balancer drive
 223
 CMU ID05 battery cell D balancer driving status
CMU ID05 Cell E Balancer drive
 224
 CMU ID05 battery cell E balancer driving status
CMU ID05 Cell F Balancer drive
 225
 CMU ID05 battery cell F balancer driving status
CMU ID05 Cell G Balancer drive
 226
 CMU ID05 battery cell G balancer driving status
CMU ID05 Cell H Balancer drive
 227
 CMU ID05 battery cell H balancer driving status
CMU ID06 Cell A Balancer drive
 228
 CMU ID06 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A93
CMU ID06 Cell B Balancer drive
 229
 CMU ID06 battery cell B balancer driving status
CMU ID06 Cell C Balancer drive
 230
 CMU ID06 battery cell C balancer driving status
CMU ID06 Cell D Balancer drive
 231
 CMU ID06 battery cell D balancer driving status
CMU ID07 Cell A Balancer drive
 232
 CMU ID07 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A94
CMU ID07 Cell B Balancer drive
 233
 CMU ID07 battery cell B balancer driving status
CMU ID07 Cell C Balancer drive
 234
 CMU ID07 battery cell C balancer driving status
CMU ID07 Cell D Balancer drive
 235
 CMU ID07 battery cell D balancer driving status
CMU ID07 Cell E Balancer drive
 236
 CMU ID07 battery cell E balancer driving status
CMU ID07 Cell F Balancer drive
 237
 CMU ID07 battery cell F balancer driving status
CMU ID07 Cell G Balancer drive
 238
 CMU ID07 battery cell G balancer driving status
CMU ID07 Cell H Balancer drive
 239
 CMU ID07 battery cell H balancer driving status
CMU ID08 Cell A Balancer drive
 240
 CMU ID08 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A95
CMU ID08 Cell B Balancer drive
 241
 CMU ID08 battery cell B balancer driving status
CMU ID08 Cell C Balancer drive
 242
 CMU ID08 battery cell C balancer driving status
CMU ID08 Cell D Balancer drive
 243
 CMU ID08 battery cell D balancer driving status
CMU ID08 Cell E Balancer drive
 244
 CMU ID08 battery cell E balancer driving status
CMU ID08 Cell F Balancer drive
 245
 CMU ID08 battery cell F balancer driving status
CMU ID08 Cell G Balancer drive
 246
 CMU ID08 battery cell G balancer driving status
CMU ID08 Cell H Balancer drive
 247
 CMU ID08 battery cell H balancer driving status
CMU ID09 Cell A Balancer drive
 248
 CMU ID09 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A96
CMU ID09 Cell B Balancer drive
 249
 CMU ID09 battery cell B balancer driving status
CMU ID09 Cell C Balancer drive
 250
 CMU ID09 battery cell C balancer driving status
CMU ID09 Cell D Balancer drive
 251
 CMU ID09 battery cell D balancer driving status
CMU ID09 Cell E Balancer drive
 252
 CMU ID09 battery cell E balancer driving status
CMU ID09 Cell F Balancer drive
 253
 CMU ID09 battery cell F balancer driving status
CMU ID09 Cell G Balancer drive
 254
 CMU ID09 battery cell G balancer driving status
CMU ID09 Cell H Balancer drive
 255
 CMU ID09 battery cell H balancer driving status
CMU ID10 Cell A Balancer drive
 256
 CMU ID10 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A97
CMU ID10 Cell B Balancer drive
 257
 CMU ID10 battery cell B balancer driving status
CMU ID10 Cell C Balancer drive
 258
 CMU ID10 battery cell C balancer driving status
CMU ID10 Cell D Balancer drive
 259
 CMU ID10 battery cell D balancer driving status
CMU ID10 Cell E Balancer drive
 260
 CMU ID10 battery cell E balancer driving status
CMU ID10 Cell F Balancer drive
 261
 CMU ID10 battery cell F balancer driving status
CMU ID10 Cell G Balancer drive
 262
 CMU ID10 battery cell G balancer driving status
CMU ID10 Cell H Balancer drive
 263
 CMU ID10 battery cell H balancer driving status
CMU ID11 Cell A Balancer drive
 264
 CMU ID11 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A98
CMU ID11 Cell B Balancer drive
 265
 CMU ID11 battery cell B balancer driving status
CMU ID11 Cell C Balancer drive
 266
 CMU ID11 battery cell C balancer driving status
CMU ID11 Cell D Balancer drive
 267
 CMU ID11 battery cell D balancer driving status
CMU ID11 Cell E Balancer drive
 268
 CMU ID11 battery cell E balancer driving status
CMU ID11 Cell F Balancer drive
 269
 CMU ID11 battery cell F balancer driving status
CMU ID11 Cell G Balancer drive
 270
 CMU ID11 battery cell G balancer driving status
CMU ID11 Cell H Balancer drive
 271
 CMU ID11 battery cell H balancer driving status
CMU ID12 Cell A Balancer drive
 272
 CMU ID12 battery cell A balancer driving status
 Electric motor switch: ON
 OFF
 Code No. P1A99
CMU ID12 Cell B Balancer drive
 273
 CMU ID12 battery cell B balancer driving status
CMU ID12 Cell C Balancer drive
 274
 CMU ID12 battery cell C balancer driving status
CMU ID12 Cell D Balancer drive
 275
 CMU ID12 battery cell D balancer driving status
Cell number specification
 276
 Battery cell number specification
 Electric motor switch: ON
 88 cell
 -
 -
note *1: Turn the electric motor switch "ON" position and connect the charging cable. Then turning the electric motor switch "LOCK" (OFF) position can check the monitor during the regular charging.

BMU monitoring items



Display on M.U.T.-III
 Item No.
 M.U.T.-III display descriptions
 Standards at each check
 Display range, and numeric value
Charge state (Control)
 1
  • Shows charging ratio of main battery.

 Electric motor switch: ON
 -5 to 120 %
Charge state (Display)
 2
  • Shows charging ratio of main battery, which gradually shows variation for meter display.

 Electric motor switch: ON
 -5 to 120 %
Battery cell maximum voltage
 3
  • Shows highest voltage in 88 battery cells.

 Electric motor switch: ON
 2.1 - 4.6 V
Maximum voltage cell ID
 4
  • Shows highest voltage cell ID in 88 battery cells.

 Electric motor switch: ON
 1 - 88
Battery cell minimum voltage
 5
  • Shows lowest voltage in 88 battery cells.

 Electric motor switch: ON
 2.1 - 4.6 V
Minimum voltage cell ID
 6
  • Shows lowest voltage cell ID in 88 battery cells.

 Electric motor switch: ON
 1 - 88
Battery total voltage
 7
  • Shows 88 total battery cell voltage.

 Electric motor switch: ON
 0 - 430 V
Module maximum temperature
 8
  • Shows highest temperature in 66 measuring points.

 Electric motor switch: ON
 -30 to 85 °C
Maximum temperature module ID
 9
  • Shows highest temperature module ID in 22 modules.

 Electric motor switch: ON
 1 - 22
Module minimum temperature
 10
  • Shows lowest temperature in 66 measuring points.

 Electric motor switch: ON
 -30 to 85 °C
Minimum temperature module ID
 11
  • Shows lowest temperature module ID in 22 modules.

 Electric motor switch: ON
 1 - 22
Internal resistance maximum
 21
  • Shows largest internal resistance of cell in 88 battery cells.

 Electric motor switch: ON
 0.0 - 12.8 mΩ
Internal resistance minimum
 22
  • Shows smallest internal resistance of cell in 88 battery cells.

 Electric motor switch: ON
 0.0 - 12.8 mΩ
Battery current capacity
 23
  • Shows battery capacity with main battery fully charged.

 Electric motor switch: ON
 0 - 60 Ah
Battery remaining capacity
 24
  • Shows residual battery level.

 Electric motor switch: ON
 0 - 60 Ah
Battery maximum input power
 25
  • Available input maximum electric power

 Electric motor switch: ON
 0.0 - 63.5 kW
Battery maximum output power
 26
  • Available output maximum electric power

 Electric motor switch: ON
 0.0 - 63.5 kW
Charge current integrated value
 27
  • Shows charging current on measuring main battery capacity.

 Electric motor switch: ON
 0 - 6500.0 Ah
Target cell voltage
 28
  • Reference voltage on activating balancer (lowest battery cell voltage)

 Electric motor switch: ON
 2.1 - 4.6 V
BAT.cell voltage difference MAX
 33
  • Difference between largest battery cell voltage and lowest battery cell voltage

 Electric motor switch: ON
 0.00 - 1.27 V
CMU ID01 Cell A voltage
 34
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID01 Cell B voltage
 35
CMU ID01 Cell C voltage
 36
CMU ID01 Cell D voltage
 37
CMU ID01 Cell E voltage
 38
CMU ID01 Cell F voltage
 39
CMU ID01 Cell G voltage
 40
CMU ID01 Cell H voltage
 41
CMU ID02 Cell A voltage
 42
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID02 Cell B voltage
 43
CMU ID02 Cell C voltage
 44
CMU ID02 Cell D voltage
 45
CMU ID02 Cell E voltage
 46
CMU ID02 Cell F voltage
 47
CMU ID02 Cell G voltage
 48
CMU ID02 Cell H voltage
 49
CMU ID03 Cell A voltage
 50
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID03 Cell B voltage
 51
CMU ID03 Cell C voltage
 52
CMU ID03 Cell D voltage
 53
CMU ID03 Cell E voltage
 54
CMU ID03 Cell F voltage
 55
CMU ID03 Cell G voltage
 56
CMU ID03 Cell H voltage
 57
CMU ID04 Cell A voltage
 58
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID04 Cell B voltage
 59
CMU ID04 Cell C voltage
 60
CMU ID04 Cell D voltage
 61
CMU ID04 Cell E voltage
 62
CMU ID04 Cell F voltage
 63
CMU ID04 Cell G voltage
 64
CMU ID04 Cell H voltage
 65
CMU ID05 Cell A voltage
 66
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID05 Cell B voltage
 67
CMU ID05 Cell C voltage
 68
CMU ID05 Cell D voltage
 69
CMU ID05 Cell E voltage
 70
CMU ID05 Cell F voltage
 71
CMU ID05 Cell G voltage
 72
CMU ID05 Cell H voltage
 73
CMU ID06 Cell A voltage
 74
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID06 Cell B voltage
 75
CMU ID06 Cell C voltage
 76
CMU ID06 Cell D voltage
 77
CMU ID07 Cell A voltage
 78
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID07 Cell B voltage
 79
CMU ID07 Cell C voltage
 80
CMU ID07 Cell D voltage
 81
CMU ID07 Cell E voltage
 82
CMU ID07 Cell F voltage
 83
CMU ID07 Cell G voltage
 84
CMU ID07 Cell H voltage
 85
CMU ID08 Cell A voltage
 86
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID08 Cell B voltage
 87
CMU ID08 Cell C voltage
 88
CMU ID08 Cell D voltage
 89
CMU ID08 Cell E voltage
 90
CMU ID08 Cell F voltage
 91
CMU ID08 Cell G voltage
 92
CMU ID08 Cell H voltage
 93
CMU ID09 Cell A voltage
 94
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID09 Cell B voltage
 95
CMU ID09 Cell C voltage
 96
CMU ID09 Cell D voltage
 97
CMU ID09 Cell E voltage
 98
CMU ID09 Cell F voltage
 99
CMU ID09 Cell G voltage
 100
CMU ID09 Cell H voltage
 101
CMU ID10 Cell A voltage
 102
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID10 Cell B voltage
 103
CMU ID10 Cell C voltage
 104
CMU ID10 Cell D voltage
 105
CMU ID10 Cell E voltage
 106
CMU ID10 Cell F voltage
 107
CMU ID10 Cell G voltage
 108
CMU ID10 Cell H voltage
 109
CMU ID11 Cell A voltage
 110
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID11 Cell B voltage
 111
CMU ID11 Cell C voltage
 112
CMU ID11 Cell D voltage
 113
CMU ID11 Cell E voltage
 114
CMU ID11 Cell F voltage
 115
CMU ID11 Cell G voltage
 116
CMU ID11 Cell H voltage
 117
CMU ID12 Cell A voltage
 118
  • Battery cell voltage is shown.

 Electric motor switch: ON
 2.1 - 4.6 V
CMU ID12 Cell B voltage
 119
CMU ID12 Cell C voltage
 120
CMU ID12 Cell D voltage
 121
CMU ID01 Module temperature1
 122
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID01 Module temperature2
 123
CMU ID01 Module temperature3
 124
CMU ID01 Module temperature4
 125
CMU ID01 Module temperature5
 126
CMU ID01 Module temperature6
 127
CMU ID02 Module temperature1
 128
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID02 Module temperature2
 129
CMU ID02 Module temperature3
 130
CMU ID02 Module temperature4
 131
CMU ID02 Module temperature5
 132
CMU ID02 Module temperature6
 133
CMU ID03 Module temperature1
 134
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID03 Module temperature2
 135
CMU ID03 Module temperature3
 136
CMU ID03 Module temperature4
 137
CMU ID03 Module temperature5
 138
CMU ID03 Module temperature6
 139
CMU ID04 Module temperature1
 140
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID04 Module temperature2
 141
CMU ID04 Module temperature3
 142
CMU ID04 Module temperature4
 143
CMU ID04 Module temperature5
 144
CMU ID04 Module temperature6
 145
CMU ID05 Module temperature1
 146
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID05 Module temperature2
 147
CMU ID05 Module temperature3
 148
CMU ID05 Module temperature4
 149
CMU ID05 Module temperature5
 150
CMU ID05 Module temperature6
 151
CMU ID06 Module temperature1
 152
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID06 Module temperature2
 153
CMU ID06 Module temperature3
 154
CMU ID07 Module temperature1
 155
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID07 Module temperature2
 156
CMU ID07 Module temperature3
 157
CMU ID07 Module temperature4
 158
CMU ID07 Module temperature5
 159
CMU ID07 Module temperature6
 160
CMU ID08 Module temperature1
 161
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID08 Module temperature2
 162
CMU ID08 Module temperature3
 163
CMU ID08 Module temperature4
 164
CMU ID08 Module temperature5
 165
CMU ID08 Module temperature6
 166
CMU ID09 Module temperature1
 167
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID09 Module temperature2
 168
CMU ID09 Module temperature3
 169
CMU ID09 Module temperature4
 170
CMU ID09 Module temperature5
 171
CMU ID09 Module temperature6
 172
CMU ID10 Module temperature1
 173
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID10 Module temperature2
 174
CMU ID10 Module temperature3
 175
CMU ID10 Module temperature4
 176
CMU ID10 Module temperature5
 177
CMU ID10 Module temperature6
 178
CMU ID11 Module temperature1
 179
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID11 Module temperature2
 180
CMU ID11 Module temperature3
 181
CMU ID11 Module temperature4
 182
CMU ID11 Module temperature5
 183
CMU ID11 Module temperature6
 184
CMU ID12 Module temperature1
 185
  • Shows module temperature.

 Electric motor switch: ON
 -30 to 85°C
CMU ID12 Module temperature2
 186
CMU ID12 Module temperature3
 187
Sum total time back up
 277
 Shows month elapsed time since vehicle manufactured.
 Electric motor switch: ON
 0 - 99,421 month
OBC integrated current value
 278
 Shows total current regularly charged since vehicle manufactured.
 Electric motor switch: ON
 0 - 4,294,967 Ah × 1,000
Quick charge integrated current
 279
 Shows total current quickly charged since vehicle manufactured.
 Electric motor switch: ON
 0 - 4,294,967 Ah × 1,000
CMU ID01 Cell A capa. (measured)
 280
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID01 Cell B capa. (measured)
 281
CMU ID01 Cell C capa. (measured)
 282
CMU ID01 Cell D capa. (measured)
 283
CMU ID01 Cell E capa. (measured)
 284
CMU ID01 Cell F capa. (measured)
 285
CMU ID01 Cell G capa. (measured)
 286
CMU ID01 Cell H capa. (measured)
 287
CMU ID02 Cell A capa. (measured)
 288
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID02 Cell B capa. (measured)
 289
CMU ID02 Cell C capa. (measured)
 290
CMU ID02 Cell D capa. (measured)
 291
CMU ID02 Cell E capa. (measured)
 292
CMU ID02 Cell F capa. (measured)
 293
CMU ID02 Cell G capa. (measured)
 294
CMU ID02 Cell H capa. (measured)
 295
CMU ID03 Cell A capa. (measured)
 296
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID03 Cell B capa. (measured)
 297
CMU ID03 Cell C capa. (measured)
 298
CMU ID03 Cell D capa. (measured)
 299
CMU ID03 Cell E capa. (measured)
 300
CMU ID03 Cell F capa. (measured)
 301
CMU ID03 Cell G capa. (measured)
 302
CMU ID03 Cell H capa. (measured)
 303
CMU ID04 Cell A capa. (measured)
 304
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID04 Cell B capa. (measured)
 305
CMU ID04 Cell C capa. (measured)
 306
CMU ID04 Cell D capa. (measured)
 307
CMU ID04 Cell E capa. (measured)
 308
CMU ID04 Cell F capa. (measured)
 309
CMU ID04 Cell G capa. (measured)
 310
CMU ID04 Cell H capa. (measured)
 311
CMU ID05 Cell A capa. (measured)
 312
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID05 Cell B capa. (measured)
 313
CMU ID05 Cell C capa. (measured)
 314
CMU ID05 Cell D capa. (measured)
 315
CMU ID05 Cell E capa. (measured)
 316
CMU ID05 Cell F capa. (measured)
 317
CMU ID05 Cell G capa. (measured)
 318
CMU ID05 Cell H capa. (measured)
 319
CMU ID06 Cell A capa. (measured)
 320
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID06 Cell B capa. (measured)
 321
CMU ID06 Cell C capa. (measured)
 322
CMU ID06 Cell D capa. (measured)
 323
CMU ID07 Cell A capa. (measured)
 324
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID07 Cell B capa. (measured)
 325
CMU ID07 Cell C capa. (measured)
 326
CMU ID07 Cell D capa. (measured)
 327
CMU ID07 Cell E capa. (measured)
 328
CMU ID07 Cell F capa. (measured)
 329
CMU ID07 Cell G capa. (measured)
 330
CMU ID07 Cell H capa. (measured)
 331
CMU ID08 Cell A capa. (measured)
 332
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID08 Cell B capa. (measured)
 333
CMU ID08 Cell C capa. (measured)
 334
CMU ID08 Cell D capa. (measured)
 335
CMU ID08 Cell E capa. (measured)
 336
CMU ID08 Cell F capa. (measured)
 337
CMU ID08 Cell G capa. (measured)
 338
CMU ID08 Cell H capa. (measured)
 339
CMU ID09 Cell A capa. (measured)
 340
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID09 Cell B capa. (measured)
 341
CMU ID09 Cell C capa. (measured)
 342
CMU ID09 Cell D capa. (measured)
 343
CMU ID09 Cell E capa. (measured)
 344
CMU ID09 Cell F capa. (measured)
 345
CMU ID09 Cell G capa. (measured)
 346
CMU ID09 Cell H capa. (measured)
 347
CMU ID10 Cell A capa. (measured)
 348
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID10 Cell B capa. (measured)
 349
CMU ID10 Cell C capa. (measured)
 350
CMU ID10 Cell D capa. (measured)
 351
CMU ID10 Cell E capa. (measured)
 352
CMU ID10 Cell F capa. (measured)
 353
CMU ID10 Cell G capa. (measured)
 354
CMU ID10 Cell H capa. (measured)
 355
CMU ID11 Cell A capa. (measured)
 356
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID11 Cell B capa. (measured)
 357
CMU ID11 Cell C capa. (measured)
 358
CMU ID11 Cell D capa. (measured)
 359
CMU ID11 Cell E capa. (measured)
 360
CMU ID11 Cell F capa. (measured)
 361
CMU ID11 Cell G capa. (measured)
 362
CMU ID11 Cell H capa. (measured)
 363
CMU ID12 Cell A capa. (measured)
 364
  • Shows single battery cell capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
CMU ID12 Cell B capa. (measured)
 365
CMU ID12 Cell C capa. (measured)
 366
CMU ID12 Cell D capa. (measured)
 367
Cell current capacity (measured)
 368
  • Shows main battery capacity after measuring main battery capacity.
  • Shows 0 Ah after turning ON electric motor switch (before measurement).
  • Value should be deleted when turning electric motor switch to LOCK (OFF) position.
  • Electric motor switch: ON
  • After measuring main battery capacity

 0.0 - 60.0 Ah
Cell current capacity difference
 369
 Shows difference recognized by BMU between main battery capacity and measured capacity results.
 Electric motor switch: ON
 - 60.0 to 60.0 Ah
Cell current capacity dif. pert
 370
 Shows ratio in difference recognized by BMU between main battery capacity and measured capacity results.
 Electric motor switch: ON
 0.0 - 500.0 %
Cell capacity (measured) MAX(01)
 371
 Shows largest battery cell capacity in main battery capacity measurement
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(01)
 372
 Shows smallest battery cell capacity in main battery capacity measurement
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(02)
 373
 Shows largest battery cell capacity in 1 previous main battery capacity measurement
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(02)
 374
 Shows smallest battery cell capacity in 1 previous main battery capacity measurement
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(03)
 375
 Shows largest battery cell capacity in 2 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(03)
 376
 Shows smallest battery cell capacity in 2 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(04)
 377
 Shows largest battery cell capacity in 3 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(04)
 378
 Shows smallest battery cell capacity in 3 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(05)
 379
 Shows largest battery cell capacity in 4 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(05)
 380
 Shows smallest battery cell capacity in 4 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(06)
 381
 Shows largest battery cell capacity in 5 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(06)
 382
 Shows smallest battery cell capacity in 5 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(07)
 383
 Shows largest battery cell capacity in 6 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(07)
 384
 Shows smallest battery cell capacity in 6 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(08)
 385
 Shows largest battery cell capacity in 7 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(08)
 386
 Shows smallest battery cell capacity in 7 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(09)
 387
 Shows largest battery cell capacity in 8 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(09)
 388
 Shows smallest battery cell capacity in 8 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MAX(10)
 389
 Shows largest battery cell capacity in 9 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity (measured) MIN(10)
 390
 Shows smallest battery cell capacity in 9 previous measurement of main battery capacity.
 Electric motor switch: ON
 0.0 - 60.0 Ah
Cell capacity measured ODO (01)
 391
 Shows odometer value on measuring main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (02)
 392
 Shows odometer value in 1 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (03)
 393
 Shows odometer value in 2 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (04)
 394
 Shows odometer value in 3 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (05)
 395
 Shows odometer value in 4 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (06)
 396
 Shows odometer value in 5 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (07)
 397
 Shows odometer value in 6 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (08)
 398
 Shows odometer value in 7 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (09)
 399
 Shows odometer value in 8 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km
Cell capacity measured ODO (10)
 400
 Shows odometer value in 9 previous measurement of main battery capacity.
 Electric motor switch: ON
 0 - 419,417 km




Yandex.Metrika
MMC-Manuals.ru